ASME B18.12-2001(R2006) Glossary of Terms for Mechanical Fasteners
|
ID： |
A29F9F0D071E4994926CBCA8FE9CCDCD |
|
文件大小(MB)： |
7.19 |
|
页数： |
70 |
|
文件格式： |
|
|
日期： |
2011-7-24 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
ASME B18.12-2001,[Revision of ASA B18.12-1962 (R1991)],GLOSSARY OF TERMS,FOR MECHANICAL,FASTENERS,A N A M E R I C A N N AT I O N A L S TA N D A R D,A N A M E R I C A N N A T I O N A L S T A N D A R D,GLOSSARY OF TERMS,FOR MECHANICAL,FASTENERS,ASME B18.12-2001,[Revision of ASA B18.12-1962 (R1991)],Date of Issuance: April 19, 2002,The 2001 edition of this Standard is being issued with an automatic addenda,subscription service. The use of an addenda allows revisions made in,response to public review comments or committee actions to be published,as necessary. The next edition of this Standard is scheduled for publication,in 2006.,ASME issues written replies to inquiries concerning interpretations of,technical aspects of this Standard. The interpretations will be included with,the above addenda service.,ASME is the registered trademark of The American Society of Mechanical Engineers.,This code or standard was developed under procedures accredited as meeting the criteria for,American National Standards. The Standards Committee that approved the code or standard,was balanced to assure that individuals from competent and concerned interests have had an,opportunity to participate. The proposed code or standard was made available for public review,and comment that provides an opportunity for additional public input from industry, academia,regulatory agencies, and the public-at-large.,ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device,or activity.,ASME does not take any position with respect to the validity of any patent rights asserted in,connection with any items mentioned in this document, and does not undertake to insure anyone,utilizing a standard against liability for infringement of any applicable letters patent, nor assume,any such liability. Users of a code or standard are expressly advised that determination of the,validity of any such patent rights, and the risk of infringement of such rights, is entirely their,own responsibility.,Participation by federal agency representative(s) or person(s) affiliated with industry is not to,be interpreted as government or industry endorsement of this code or standard.,ASME accepts responsibility for only those interpretations of this document issued in,accordance with the established ASME procedures and policies, which precludes the issuance,of interpretations by individuals.,No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.,The American Society of Mechanical Engineers,Three Park Avenue, New York, NY 10016-5990,Copyright . 2002 by,THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS,All Rights Reserved,Printed in U.S.A.,CONTENTS,Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv,Committee Roster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v,Correspondence With the B18 Committee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii,1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2.1 Basic Fastener Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2.2 Fastener Characteristics (Excluding Head Styles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,2.3 Fastener Head Styles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,2.4 Dimensional Terms and Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12,2.5 Terms Relating to the Manufacture of Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17,2.6 Fastener Performance Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19,2.7 Terms Relating to Material and Heat Treatment of Fasteners . . . . . . . . . . . . . . . . . 20,2.8 Coatings and Finish Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20,2.9 Quality Assurance Including Inspection Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 21,2.10 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . .……
……